Priced by the gram
The price comes from the grams of filament. Grams are pooled per material group across the order, and your part's grams are estimated from its file.
PLA, PLA+, PETG and ABS are priced together; their grams are pooled.
- Total
- ₺1,300
- Per gram
- ₺4.33
| Total | ₺1,300 |
|---|---|
| Per gram | ₺4.33 |
| Tier | 200 to 500 g |
This is the tariff price of the grams you entered. Your part's grams are estimated from its file; we confirm the final price in the DM before you order.
Not sure of the grams? Type the filament weight your slicer shows, or upload your file on the quote page; the grams are estimated from the part's geometry.
For ABS, the grams your slicer shows count ×1.19 on the tariff.
The whole tariff
Each tier applies only to the grams inside it: the first 200 g count at the first price, 200 to 500 g at the second, everything over 500 g at the third. Grams are pooled within a group, so adding a part can lower the price per gram. Groups stay apart: a cheap PLA part does not carry a PA-12 part into a lower tier.
ABS is priced at PLA's density (1.24 g/cm³): a gram of ABS counts as about 1.19 g.
| Tier | Standard, selected | TPU | PA-12 |
|---|---|---|---|
| Price per gram | |||
| First 200 g | ₺5.00 | ₺10.00 | ₺15.00 |
| 200–500 g | ₺3.00 | ₺8.50 | ₺12.50 |
| Over 500 g | ₺2.50 | ₺7.00 | ₺11.00 |
| Total | |||
| 200 g | ₺1,000 | ₺2,000 | ₺3,000 |
| 500 g | ₺1,900 | ₺4,550 | ₺6,750 |
| 1,000 g | ₺3,150 | ₺8,050 | ₺12,250 |
Layer height and infill
Both are chosen per part. Layer height changes the price by a factor, infill changes the grams.
Layer height
0.20 mm is the standard price. A finer layer multiplies the part's share of its group's filament price; the price per gram still comes from the pooled grams, and inserts and the prime tower are not multiplied.
| Layer | Factor | 10 brackets, estimated |
|---|---|---|
| 0.08 mm | × 1.6 | ₺1,822 |
| 0.12 mm | × 1.4 | ₺1,595 |
| 0.16 mm | × 1.2 | ₺1,367 |
| 0.20 mmstandard | × 1.0 | ₺1,139 |
Infill
Infill fills the inside of the part. It has no factor; it changes the grams, and the price with them. Walls and top and bottom skins stay the same at every setting. 15% is standard; 100% prints solid.
| Infill | One bracket, estimated | 10 brackets, estimated |
|---|---|---|
| 15%standard | 24.6 g | ₺1,139 |
| 30% | 29.6 g | ₺1,289 |
| 50% | 36.3 g | ₺1,490 |
| 100% | 54.2 g | ₺2,005 |
Example: the site's example bracket (96 × 62 × 24 mm, PLA), no support, 10 pieces. The grams are estimated from the geometry. The layer table at 15% infill, the infill table at 0.20 mm layers.
Support and prime tower
You choose the support. We measure the faces of the part that point down; when the part needs support, the support's grams are added to the estimate.
| Option | What happens, and the price |
|---|---|
| No support | The part prints without support.No extra grams. |
| Support | Tree supports print under the overhangs and are removed after printing.The support's grams are estimated from the volume under the overhangs and added to the part's. |
| Support with interface | A second filament goes between the support and the part, and a prime tower is added to the print.The support's grams and the prime tower's grams are added. |
Interface filament
The interface is always a different filament from the part's.
| Part | Interface |
|---|---|
| PLA and PLA+ | PETG |
| PETG, ABS, PA-12 and TPU | PLA |
Prime tower
A small tower printed beside the part to prime the nozzle when the filament changes. One per plate; its base is fixed, and it rises to the highest supported overhang among the parts that use an interface. Its grams are priced in the material group of the part it stands beside.
Polyurethane casting
First a silicone mould is taken from your part, then the pieces are cast into it in polyurethane. The price is approximate.
- Mould: silicone at 10 times the part's volume (1.10 g/cm³), ₺2,000 a kilogram.
- Each piece: polyurethane resin (1.05 g/cm³), ₺650 a kilogram.
- One mould casts 20 pieces; a new mould is poured for every 20.
The mould's life is taken from common figures for classic silicone moulds; the densities are generic values for silicone and resin.
Casting the example bracket
Example: the site's example bracket, 43.7 cm³.
| Pieces | Moulds | Approximate total | Per piece |
|---|---|---|---|
| 1 | 1 | ₺992 | ₺992 |
| 10 | 1 | ₺1,260 | ₺126 |
| 50 | 3 | ₺4,377 | ₺88 |
| 200 | 10 | ₺15,584 | ₺78 |
| 1,000 | 50 | ₺77,918 | ₺78 |
- Mould: 43.7 cm³ × 10 × 1.10 g/cm³ = 481 g of silicone, ₺962.
- Resin: 43.7 cm³ × 1.05 g/cm³ = 45.9 g, ₺30 a piece.
Injection molding
No fixed price: we work it out together from the mould and the quantity. Send your part and the quantity.
Get in touchHeat-set inserts
| Thread | Length | Price, each |
|---|---|---|
| M2 | 3 mm | ₺15 |
| M3 | 5.75 mm | ₺15 |
| M4 | 4 mm | ₺15 |
| M6 | 8 mm | ₺40 |
Threaded inserts set with heat; fitting is included in the price. FDM prints only, and you choose how many per part. Inserts sit outside the gram tariff and are not multiplied by the layer factor.
Minimum order
₺250
An order that totals less than ₺250 is charged ₺250, whatever the method. The part prices stay as they are; only the total is raised.
In the standard group that is about 50 g of filament. One example bracket comes to an estimated ₺123 on the tariff; as an order it is ₺250.
All prices include VAT. The buyer pays for shipping: orders go to Aras Kargo in about 2 days on average. Hand delivery in Etimesgut (Ankara) too.
See the tariff on your own part.
Upload your file